Obi-Wan Kenobi Full Season Download

-
 As a student, I get bored. I find stuff to watch or play and this show has me hooked. Liked it so much I decided to share it with you guys. Enjoy. S1.1   S1.2   S1.3   S1.4   S1.5   S1.6  
Post a Comment

NTC/362: Fundamentals of Networking

-

 NTC/362: Fundamentals of Networking

Q: Refer to the download; which options are true about the OSPF configuration?

R2#show ip ospf interface
FastEthernet0/0 is up, line protocol is up
  Internet Address 20.20.20.1/24, Area 0, Attached via Network Statement
  Process ID 10, Router ID 20.20.20.1, Network Type BROADCAST, Cost: 1
  Topology-MTID    Cost    Disabled    Shutdown      Topology Name
        0           1         no          no            Base
  Transmit Delay is 1 sec, State BDR, Priority 1
  Designated Router (ID) 20.20.20.2, Interface address 20.20.20.2
  Backup Designated router (ID) 20.20.20.1, Interface address 20.20.20.1
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:01
  Supports Link-local Signaling (LLS)
  Cisco NSF helper support enabled
  IETF NSF helper support enabled
  Index 1/1, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 2
  Last flood scan time is 0 msec, maximum is 0 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 20.20.20.2  (Designated Router)
  Suppress hello for 0 neighbor(s)
FastEthernet0/1 is up, line protocol is up
  Internet Address 10.10.10.2/24, Area 0.0.0.2, Attached via Interface Enable
  Process ID 10, Router ID 20.20.20.1, Network Type BROADCAST, Cost: 1
  Topology-MTID    Cost    Disabled    Shutdown      Topology Name
        0           1         no          no            Base
  Enabled by interface config, including secondary ip addresses
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 20.20.20.1, Interface address 10.10.10.2
  Backup Designated router (ID) 10.10.10.1, Interface address 10.10.10.1
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:03
  Supports Link-local Signaling (LLS)
  Cisco NSF helper support enabled
  IETF NSF helper support enabled
  Index 1/2, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 2, maximum is 2
  Last flood scan time is 0 msec, maximum is 0 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 10.10.10.1  (Backup Designated Router)
  Suppress hello for 0 neighbor(s)
R2#

Each correct answer represents a complete solution. Choose all that apply.

A: R2's F0/1 is configured using the OSPF interface configuration, R2 is configured in two OSPF areas: 0 and 2.

Explanation: The download shows that R2 is configured into two different areas: 0 and 0.0.0.2 (which is the dotted-decimal version of area 2). It also shows that its F0/0 interface has been configured using a network statement and its F0/1 interface has been configured using interface OSPF commands.

Comments

Post a Comment

Popular posts from this blog

-
 CYB 205 Infrastructure Administration Q: Jim is implementing an IDaaS solution for his organization. What type of technology is he putting in place? A: Identity as a service Explanation: Jim is using the IDaaS (Identity as a service) technology, which provides an identity platform as a third-party service. It is a cloud-based service for obtaining subscription-based identity management and access control capabilities.Answers B and C are incorrect. These are the invalid choices.Answer D is incorrect. OAuth is a standard that applications can use to provide client applications with secure delegated access.
Read more
-
 CYB 205 Infrastructure Administration Q: Alejandro is an incident response analyst for a large corporation. He is on the midnight shift when an intrusion detection system alerts him to a potential brute-force password attack against one of the company’s critical information systems. He performs an initial triage of the event before taking any additional action. A: Activate the incident response team. Explanation: The incident response process consists of a series of steps that start with detection and run through response, mitigation, reporting, recovery, and remediation, ending with a lessons learned and onward preparation phase. After the detection of a security incident, the next step in the process is the response, which should follow the organization’s formal incident response procedure. The first step of this procedure is activating the appropriate teams, including the organization's computer security incident response team (CSIRT).Answers A and D are incorrect. Lessons lear...
Read more
-
 CYB 205 Infrastructure Administration Q: Elaine is developing a business continuity plan for her organization. What value should she seek to minimize? A: RTO Explanation: Elaine should seek to minimize the recovery time objective value. The goal of business continuity planning exercises is to reduce the amount of time required to restore operations. This is done by minimizing the recovery time objective (RTO). RTO is the amount of time expected to return an IT service or component to operation after a failure.Answer C is incorrect. SLAs (service-level agreements) are written contracts that document service expectations.Answers B and D are incorrect. The Secure Socket Layer (SSL) and the Lightweight Directory Access Protocol (LDAP) are the network protocols.
Read more